-------------------------------------------------
ACIS LOAD REVIEW OUTPUT:
FOR REVIEW BY CXC ACIS OPS PERSONNEL
-------------------------------------------------
USING /data/acis/LoadReviews/2024/OCT1324/oflsb/CR287_0104.backstop
LOAD HISTORY FROM: /data/acis/LoadReviews/2024/OCT1324/oflsb/ACIS-History_edit.txt
-- CHANDRA LOAD START --
CHANDRA STATUS ARRAY AT START OF LOAD REVIEW (FROM PREVIOUS LOAD HISTORY FILE):
(FP SI,HETG status,LETG status,current OBSID,RadMon status,current TLM FMT,Dither)
= (HRC-S,HETG-IN,LETG-OUT,43058,OORMPDS,CSELFMT2,ENAB)
2024:287:01:27:00.000 2298712 ACISPKT AA00000000
ACISPKT AND/OR POWER COMMAND ERROR:
2024:287:01:27:03.00 ACISPKT Rule #0 - ERROR Less than 4 second delay between consecutive ACISPKT commands
2024:287:01:27:03.000 2298723 ACISPKT AA00000000
2024:287:01:28:00.000 2298946 ACISPKT AA00000000
2024:287:01:28:04.000 2298961 ACISPKT WSPOW0002A
==> WSPOW COMMAND LOADS: Feps 1 3 5; All vids down
2024:287:01:29:07.000 2299207 ACISPKT RS_0000001
2024:287:01:56:39.766 2305657 COMMAND_SW OORMPEN
==> Exit leg pad time is 24803.80 ks.
>>>ERROR: RadMon EN occurs well after an E1 exit (>15ks).
-OR- RadMon EN encountered prior to a XE1RADZ0/XEF1000.
2024:287:01:56:40.766 2305661 SIMTRANS 75624 (ACIS-S)
==> THERE IS A Z-SIM OF 0.00 mm FOR THIS OBSERVATION.
2024:287:01:56:40.766 2305661 ACISPKT AA00000000
2024:287:01:56:41.766 2305665 MP_OBSID 30566
==> ObsID change occurs 0.0 minutes after stop science.
>>>ERROR: ObsID change occurs less than 3 minutes after a stop science command.
LATEST OCAT INFO FOR OBSID 30566:
Target Name: AT2024wpp SI Mode: TE_0057A
Instrument: ACIS-S Grating: NONE Type: DDT
Exposure Time: 20 Remaining Exposure time: 20
Offset: Y: 0 Z: 0 Z-sim:
ACIS Exposure Mode: TE Event TM Format: VF Frame Time:
Chips Turned On: NNNN NNYYNN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 25 Obj_Flag: NO
2024:287:01:56:44.766 2305677 ACISPKT AA00000000
2024:287:01:56:48.766 2305692 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:287:01:57:12.766 2305786 ACISPKT WSPOW0C006
==> WSPOW COMMAND LOADS: Feps 1 2; S2 S3
2024:287:01:58:15.766 2306032 ACISPKT WT0057A034
ACIS PBLOCK LOADS:
parameterBlockId = 0x0057a034
fepCcdSelect = 10 7 6 10 10 10
fepMode = 3 # FEP_TE_MODE_EV5x5
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 30
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:287:01:58:19.766 2306047 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 30566
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_0057AB is WT0057A034 and is stored.
>>>ERROR: Problem with Instrument configuration
Please check the following errors
- Requested Grating is NOT inserted.
Requested:NONE Actual:HETG
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-S,HETG-IN,LETG-OUT,30566,OORMPEN,CSELFMT2,ENAB)
2024:287:01:58:23.766 2306063 ACISPKT RS_0000001
2024:287:01:58:27.766 2306079 ACISPKT RH_0000001
2024:287:07:47:51.766 2387889 ACISPKT AA00000000
==> ACIS integration time of 20.00 ks.
This is 100.00% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:287:07:47:51.766 2387889 SIMTRANS -50504 (HRC-I)
2024:287:07:50:51.766 2388592 COMMAND_HW CSELFMT1
2024:287:07:50:51.766 2388592 MP_OBSID 28001
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 28001:
No ACIS info found for obsid 28001.
This is an HRC-I observation.
2024:287:07:50:51.766 2388592 ACISPKT AA00000000
2024:287:07:50:55.766 2388607 ACISPKT AA00000000
2024:287:07:50:59.766 2388623 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:287:07:51:23.766 2388717 ACISPKT WSPOW08812
==> WSPOW COMMAND LOADS: Feps 1 4; I3 S3
2024:287:07:52:21.166 2388941 SIMFOCUS -716
2024:287:07:52:26.766 2388962 ACISPKT RS_0000001
2024:287:07:52:30.766 2388978 ACISPKT RH_0000001
2024:287:07:52:53.766 2389068 ACISPKT WT00DAA014
ACIS PBLOCK LOADS:
parameterBlockId = 0x00daa014
fepCcdSelect = 10 7 10 10 3 10
fepMode = 2 # FEP_TE_MODE_EV3x3
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 0
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 33
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3750
windowSlotIndex = 4
2024:287:07:52:57.766 2389083 ACISPKT W200138014
ACIS 2D WINDOW BLOCK LOADS:
windowSlotIndex = 4
windowBlockId = 0x00138014
ccdId = 0
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 1
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 2
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 3
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 4
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 5
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 6
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 7
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 8
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 9
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
2024:287:07:53:01.766 2389099 ACISPKT XTZ0000005
====> CHANDRA STATUS ARRAY=(HRC-I,HETG-IN,LETG-OUT,28001,OORMPEN,CSELFMT1,ENAB)
2024:287:08:12:50.250 2393737 AOENDITH AOENDITH
==> DITHER ENABLED
2024:287:08:25:22.766 SCS-134 Activation: HRC Observation Begun
Time between SI Mode load start and SCS-134 activation is good:
Required Delta T: 2071.0 Actual Delta T: 2071.0
2024:287:11:18:32.766 2437220 SIMTRANS 92904 (ACIS-I)
==> THERE IS A Z-SIM OF 0.00 mm FOR THIS OBSERVATION.
>>>ERROR: SIM TRANSLATION OCCURS 205.52 minutes AFTER A START SCIENCE.
2024:287:11:18:44.766 2437267 ACISPKT AA00000000
==> ACIS integration time of 0.01 ks.
This is 100.00% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:287:11:18:44.766 215PCAOF command: HRC Observation Ends
2024:287:11:18:46.766 2437275 COMMAND_HW CSELFMT2
2024:287:11:18:46.766 2437275 MP_OBSID 30563
==> ObsID change occurs 0.0 minutes after stop science.
>>>ERROR: ObsID change occurs less than 3 minutes after a stop science command.
LATEST OCAT INFO FOR OBSID 30563:
Target Name: A85 North SI Mode: TE_006E6
Instrument: ACIS-I Grating: NONE Type: GO
Exposure Time: 18 Remaining Exposure time: 18
Offset: Y: 0 Z: 0 Z-sim:
ACIS Exposure Mode: TE Event TM Format: VF Frame Time:
Chips Turned On: YYYY NNNNNN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 25 Obj_Flag: NO
2024:287:11:23:26.166 2438365 SIMFOCUS -486
2024:287:11:24:47.566 2438683 SIMFOCUS -536
2024:287:11:30:01.285 REAL-TIME COMM BEGINS 2024:287:07:30:01.285 EDT
2024:287:11:37:48.145 2441729 ACISPKT AA00000000
2024:287:11:37:52.145 2441744 ACISPKT AA00000000
2024:287:11:37:56.145 2441760 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:287:11:38:20.145 2441854 ACISPKT WSPOW00F1E
==> WSPOW COMMAND LOADS: Feps 1 2 3 4; I0 I1 I2 I3
2024:287:11:39:23.145 2442100 ACISPKT WT006E6034
ACIS PBLOCK LOADS:
parameterBlockId = 0x006e6034
fepCcdSelect = 10 3 2 1 0 10
fepMode = 3 # FEP_TE_MODE_EV5x5
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 31
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:287:11:39:27.145 2442115 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 30563
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_006E6B is WT006E6034 and is stored.
>>>ERROR: Problem with Instrument configuration
Please check the following errors
- Requested Grating is NOT inserted.
Requested:NONE Actual:HETG
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-I,HETG-IN,LETG-OUT,30563,OORMPEN,CSELFMT2,ENAB)
2024:287:11:39:31.145 2442131 ACISPKT RS_0000001
2024:287:11:39:35.145 2442146 ACISPKT RH_0000001
2024:287:11:53:35.145 2445424 AOENDITH AOENDITH
==> DITHER ENABLED
2024:287:13:00:01.285 REAL-TIME COMM ENDS 2024:287:09:00:01.285 EDT
==> COMM DURATION: 90.00 mins.
2024:287:16:51:45.145 2515239 ACISPKT AA00000000
==> ACIS integration time of 17.50 ks.
This is 97.22% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:287:16:54:45.145 2515942 MP_OBSID 28321
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 28321:
Target Name: PSZ2G342.51-50.97 SI Mode: TE_006E6
Instrument: ACIS-I Grating: NONE Type: GO
Exposure Time: 9.34607 Remaining Exposure time: 9.34607
Offset: Y: 0 Z: 0 Z-sim:
ACIS Exposure Mode: TE Event TM Format: VF Frame Time:
Chips Turned On: YYYY NNNNNN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 25 Obj_Flag: NO
2024:287:17:17:32.295 2521277 ACISPKT WSVIDALLDN
2024:287:17:17:50.295 2521347 ACISPKT WSPOW00F1E
==> WSPOW COMMAND LOADS: Feps 1 2 3 4; I0 I1 I2 I3
2024:287:17:18:53.295 2521593 ACISPKT WT006E7034
ACIS PBLOCK LOADS:
parameterBlockId = 0x006e7034
fepCcdSelect = 10 3 2 1 0 10
fepMode = 3 # FEP_TE_MODE_EV5x5
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 0
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 31
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:287:17:18:57.295 2521608 ACISPKT RS_0000001
2024:287:17:19:01.295 2521624 ACISPKT RH_0000001
2024:287:17:19:24.295 2521714 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 28321
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_006E6 is WT006E7034 and is stored.
>>>ERROR: Problem with Instrument configuration
Please check the following errors
- Requested Grating is NOT inserted.
Requested:NONE Actual:HETG
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-I,HETG-IN,LETG-OUT,28321,OORMPEN,CSELFMT2,ENAB)
2024:287:17:40:01.285 REAL-TIME COMM BEGINS 2024:287:13:40:01.285 EDT
2024:287:19:10:01.285 REAL-TIME COMM ENDS 2024:287:15:10:01.285 EDT
==> COMM DURATION: 90.00 mins.
2024:287:19:55:17.365 2558214 ACISPKT AA00000000
==> ACIS integration time of 9.35 ks.
This is 100.07% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:287:19:55:17.365 2558214 SIMTRANS -50504 (HRC-I)
2024:287:19:58:17.365 2558916 COMMAND_HW CSELFMT1
2024:287:19:58:17.365 2558916 MP_OBSID 30560
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 30560:
No ACIS info found for obsid 30560.
This is an HRC-I observation.
2024:287:19:58:17.365 2558916 ACISPKT AA00000000
2024:287:19:58:21.365 2558932 ACISPKT AA00000000
2024:287:19:58:25.365 2558947 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:287:19:58:49.365 2559041 ACISPKT WSPOW08812
==> WSPOW COMMAND LOADS: Feps 1 4; I3 S3
2024:287:19:59:52.365 2559287 ACISPKT RS_0000001
2024:287:19:59:56.365 2559302 ACISPKT RH_0000001
2024:287:20:00:10.765 2559359 SIMFOCUS -716
2024:287:20:00:19.365 2559392 ACISPKT WT00DAA014
ACIS PBLOCK LOADS:
parameterBlockId = 0x00daa014
fepCcdSelect = 10 7 10 10 3 10
fepMode = 2 # FEP_TE_MODE_EV3x3
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 0
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 33
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3750
windowSlotIndex = 4
2024:287:20:00:23.365 2559408 ACISPKT W200138014
ACIS 2D WINDOW BLOCK LOADS:
windowSlotIndex = 4
windowBlockId = 0x00138014
ccdId = 0
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 1
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 2
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 3
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 4
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 5
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 6
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 7
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 8
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 9
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
2024:287:20:00:27.365 2559423 ACISPKT XTZ0000005
====> CHANDRA STATUS ARRAY=(HRC-I,HETG-IN,LETG-OUT,30560,OORMPEN,CSELFMT1,ENAB)
2024:287:20:27:16.007 2565701 AOENDITH AOENDITH
==> DITHER ENABLED
2024:287:20:32:48.365 SCS-134 Activation: HRC Observation Begun
Time between SI Mode load start and SCS-134 activation is good:
Required Delta T: 2071.0 Actual Delta T: 2071.0
2024:287:23:24:22.365 2607170 SIMTRANS 75624 (ACIS-S)
==> THERE IS A Z-SIM OF 0.00 mm FOR THIS OBSERVATION.
>>>ERROR: SIM TRANSLATION OCCURS 203.92 minutes AFTER A START SCIENCE.
2024:287:23:24:34.365 215PCAOF command: HRC Observation Ends
2024:287:23:24:34.365 2607217 ACISPKT AA00000000
==> ACIS integration time of 0.01 ks.
This is 100.00% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:287:23:24:36.365 2607224 COMMAND_HW CSELFMT2
2024:287:23:24:36.365 2607224 MP_OBSID 28549
==> ObsID change occurs 0.0 minutes after stop science.
>>>ERROR: ObsID change occurs less than 3 minutes after a stop science command.
LATEST OCAT INFO FOR OBSID 28549:
Target Name: NGC1566 SI Mode: TE_0046E
Instrument: ACIS-S Grating: NONE Type: GO
Exposure Time: 30 Remaining Exposure time: 30
Offset: Y: -1.5 Z: 0 Z-sim:
ACIS Exposure Mode: TE Event TM Format: VF Frame Time:
Chips Turned On: NNYY NYYYNN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 25 Obj_Flag: NO
2024:287:23:27:22.103 2607871 ACISPKT AA00000000
2024:287:23:27:26.103 2607887 ACISPKT AA00000000
ACISPKT AND/OR POWER COMMAND ERROR:
2024:287:23:27:30.10 ACISPKT Rule #1 - ERROR LESS THAN 3 min delay between first AA00 and WSPOW
2024:287:23:27:30.103 2607902 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:287:23:27:54.103 2607996 ACISPKT WSPOW0EC3E
==> WSPOW COMMAND LOADS: Feps 1 2 3 4 5; I2 I3 S1 S2 S3
2024:287:23:28:51.765 2608221 SIMFOCUS -418
2024:287:23:28:57.103 2608242 ACISPKT WT0046E034
ACIS PBLOCK LOADS:
parameterBlockId = 0x0046e034
fepCcdSelect = 10 7 5 6 3 2
fepMode = 3 # FEP_TE_MODE_EV5x5
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 31
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:287:23:29:01.103 2608257 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 28549
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_0046EB is WT0046E034 and is stored.
>>>ERROR: Problem with Instrument configuration
Please check the following errors
- Requested Grating is NOT inserted.
Requested:NONE Actual:HETG
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-S,HETG-IN,LETG-OUT,28549,OORMPEN,CSELFMT2,ENAB)
2024:287:23:29:05.103 2608273 ACISPKT RS_0000001
2024:287:23:29:09.103 2608289 ACISPKT RH_0000001
2024:287:23:30:14.165 2608543 SIMFOCUS -468
2024:287:23:45:09.103 2612035 AOENDITH AOENDITH
==> DITHER ENABLED
2024:288:00:35:01.285 REAL-TIME COMM BEGINS 2024:288:20:35:01.285 EDT
2024:288:02:05:01.285 REAL-TIME COMM ENDS 2024:287:22:05:01.285 EDT
==> COMM DURATION: 90.00 mins.
2024:288:04:18:46.456 2644789 ORBPOINT EAPOGEE
2024:288:08:11:39.103 2730630 ACISPKT AA00000000
==> ACIS integration time of 30.00 ks.
This is 100.00% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:288:08:11:39.103 2730630 SIMTRANS 92904 (ACIS-I)
==> THERE IS A Z-SIM OF 0.00 mm FOR THIS OBSERVATION.
2024:288:08:13:38.503 2731096 SIMFOCUS -536
2024:288:08:14:39.103 2731333 MP_OBSID 28600
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 28600:
Target Name: Abell 370 SI Mode: TE_006E6
Instrument: ACIS-I Grating: NONE Type: GO
Exposure Time: 13 Remaining Exposure time: 13
Offset: Y: 0 Z: 0 Z-sim:
ACIS Exposure Mode: TE Event TM Format: VF Frame Time:
Chips Turned On: YYYY NNNNNN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 25 Obj_Flag: NO
2024:288:08:17:56.347 2732102 ACISPKT AA00000000
2024:288:08:18:00.347 2732118 ACISPKT AA00000000
2024:288:08:18:04.347 2732134 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:288:08:18:28.347 2732227 ACISPKT WSPOW00F1E
==> WSPOW COMMAND LOADS: Feps 1 2 3 4; I0 I1 I2 I3
2024:288:08:19:31.347 2732473 ACISPKT WT006E6034
ACIS PBLOCK LOADS:
parameterBlockId = 0x006e6034
fepCcdSelect = 10 3 2 1 0 10
fepMode = 3 # FEP_TE_MODE_EV5x5
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 31
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:288:08:19:35.347 2732489 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 28600
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_006E6B is WT006E6034 and is stored.
>>>ERROR: Problem with Instrument configuration
Please check the following errors
- Requested Grating is NOT inserted.
Requested:NONE Actual:HETG
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-I,HETG-IN,LETG-OUT,28600,OORMPEN,CSELFMT2,ENAB)
2024:288:08:19:39.347 2732504 ACISPKT RS_0000001
2024:288:08:19:43.347 2732520 ACISPKT RH_0000001
2024:288:11:25:01.285 REAL-TIME COMM BEGINS 2024:288:07:25:01.285 EDT
2024:288:12:16:53.347 2788052 ACISPKT AA00000000
==> ACIS integration time of 13.00 ks.
This is 100.00% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:288:12:16:53.347 2788052 SIMTRANS 92560 (ACIS-I)
==> THERE IS A Z-SIM OF -0.87 mm FOR THIS OBSERVATION.
2024:288:12:19:53.347 2788754 MP_OBSID 28352
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 28352:
Target Name: PSR J1101-6101 SI Mode: TE_006E6
Instrument: ACIS-I Grating: NONE Type: GO
Exposure Time: 10 Remaining Exposure time: 10
Offset: Y: -0.3 Z: 0 Z-sim: -0.8775
ACIS Exposure Mode: TE Event TM Format: VF Frame Time:
Chips Turned On: YYYY NNNNNN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 25 Obj_Flag: NO
2024:288:12:53:45.809 2796686 ACISPKT WSVIDALLDN
2024:288:12:54:03.809 2796756 ACISPKT WSPOW00F1E
==> WSPOW COMMAND LOADS: Feps 1 2 3 4; I0 I1 I2 I3
2024:288:12:55:01.285 REAL-TIME COMM ENDS 2024:288:08:55:01.285 EDT
==> COMM DURATION: 90.00 mins.
2024:288:12:55:06.809 2797002 ACISPKT WT006E7034
ACIS PBLOCK LOADS:
parameterBlockId = 0x006e7034
fepCcdSelect = 10 3 2 1 0 10
fepMode = 3 # FEP_TE_MODE_EV5x5
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 0
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 31
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:288:12:55:10.809 2797017 ACISPKT RS_0000001
2024:288:12:55:14.809 2797033 ACISPKT RH_0000001
2024:288:12:55:37.809 2797123 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 28352
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_006E6 is WT006E7034 and is stored.
>>>ERROR: Problem with Instrument configuration
Please check the following errors
- Requested Grating is NOT inserted.
Requested:NONE Actual:HETG
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-I,HETG-IN,LETG-OUT,28352,OORMPEN,CSELFMT2,ENAB)
2024:288:15:42:24.809 2836174 ACISPKT AA00000000
==> ACIS integration time of 10.01 ks.
This is 100.07% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:288:15:42:24.809 2836174 SIMTRANS 92904 (ACIS-I)
==> THERE IS A Z-SIM OF 0.00 mm FOR THIS OBSERVATION.
2024:288:15:45:24.809 2836877 MP_OBSID 28827
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 28827:
Target Name: Abell 168 North SI Mode: TE_006E6
Instrument: ACIS-I Grating: NONE Type: GTO
Exposure Time: 13 Remaining Exposure time: 13
Offset: Y: 0 Z: 0 Z-sim:
ACIS Exposure Mode: TE Event TM Format: VF Frame Time:
Chips Turned On: YYYY NNNNNN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 25 Obj_Flag: NO
2024:288:16:21:38.880 2845361 ACISPKT WSVIDALLDN
2024:288:16:21:56.880 2845431 ACISPKT WSPOW00F1E
==> WSPOW COMMAND LOADS: Feps 1 2 3 4; I0 I1 I2 I3
2024:288:16:22:59.880 2845677 ACISPKT WT006E7034
ACIS PBLOCK LOADS:
parameterBlockId = 0x006e7034
fepCcdSelect = 10 3 2 1 0 10
fepMode = 3 # FEP_TE_MODE_EV5x5
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 0
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 31
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:288:16:23:03.880 2845693 ACISPKT RS_0000001
2024:288:16:23:07.880 2845708 ACISPKT RH_0000001
2024:288:16:23:30.880 2845798 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 28827
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_006E6 is WT006E7034 and is stored.
>>>ERROR: Problem with Instrument configuration
Please check the following errors
- Requested Grating is NOT inserted.
Requested:NONE Actual:HETG
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-I,HETG-IN,LETG-OUT,28827,OORMPEN,CSELFMT2,ENAB)
2024:288:17:15:01.285 REAL-TIME COMM BEGINS 2024:288:13:15:01.285 EDT
2024:288:18:45:01.285 REAL-TIME COMM ENDS 2024:288:14:45:01.285 EDT
==> COMM DURATION: 90.00 mins.
2024:288:19:43:37.880 2892655 ACISPKT AA00000000
==> ACIS integration time of 12.01 ks.
This is 92.36% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:288:19:43:37.880 2892655 SIMTRANS 75624 (ACIS-S)
==> THERE IS A Z-SIM OF 0.00 mm FOR THIS OBSERVATION.
2024:288:19:45:37.280 2893121 SIMFOCUS -418
2024:288:19:46:37.880 2893357 MP_OBSID 28553
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 28553:
Target Name: NGC7496 SI Mode: TE_006CC
Instrument: ACIS-S Grating: NONE Type: GO
Exposure Time: 30 Remaining Exposure time: 30
Offset: Y: -1.5 Z: 0 Z-sim:
ACIS Exposure Mode: TE Event TM Format: VF Frame Time:
Chips Turned On: NNYY NNYYNN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 25 Obj_Flag: NO
2024:288:19:46:56.680 2893430 SIMFOCUS -468
2024:288:19:49:01.185 2893916 ACISPKT AA00000000
2024:288:19:49:05.185 2893932 ACISPKT AA00000000
2024:288:19:49:09.185 2893947 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:288:19:49:33.185 2894041 ACISPKT WSPOW0CC1E
==> WSPOW COMMAND LOADS: Feps 1 2 3 4; I2 I3 S2 S3
2024:288:19:50:36.185 2894287 ACISPKT WT006CC034
ACIS PBLOCK LOADS:
parameterBlockId = 0x006cc034
fepCcdSelect = 10 7 6 3 2 10
fepMode = 3 # FEP_TE_MODE_EV5x5
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 31
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:288:19:50:40.185 2894303 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 28553
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_006CCB is WT006CC034 and is stored.
>>>ERROR: Problem with Instrument configuration
Please check the following errors
- Requested Grating is NOT inserted.
Requested:NONE Actual:HETG
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-S,HETG-IN,LETG-OUT,28553,OORMPEN,CSELFMT2,ENAB)
2024:288:19:50:44.185 2894318 ACISPKT RS_0000001
2024:288:19:50:48.185 2894334 ACISPKT RH_0000001
2024:289:00:00:01.285 REAL-TIME COMM BEGINS 2024:289:20:00:01.285 EDT
2024:289:01:30:01.285 REAL-TIME COMM ENDS 2024:288:21:30:01.285 EDT
==> COMM DURATION: 90.00 mins.
2024:289:04:12:53.964 3011898 ACISPKT AA00000000
==> ACIS integration time of 28.90 ks.
This is 96.32% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:289:04:12:53.964 3011898 SIMTRANS -99616 (HRC-S)
2024:289:04:15:53.964 3012600 COMMAND_HW CSELFMT6
2024:289:04:15:53.964 3012600 MP_OBSID 43071
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 43071:
No ocat info found for obsid 43071
2024:289:04:16:28.303 3012734 COMMAND_SW 4OHETGIN
2024:289:04:18:31.364 3013215 COMMAND_SW OORMPDS
==>The requested SI_MODE for the inbound CTI is TE_007AC
2024:289:04:18:31.364 3013215 ACISPKT AA00000000
2024:289:04:18:35.364 3013230 ACISPKT AA00000000
2024:289:04:18:39.364 3013246 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:289:04:19:03.364 3013339 ACISPKT WSPOW0CF3F
==> WSPOW COMMAND LOADS: All Feps; std I array
2024:289:04:20:06.364 3013585 ACISPKT WT007AC024
ACIS PBLOCK LOADS:
parameterBlockId = 0x007ac024
fepCcdSelect = 3 7 0 1 2 6
fepMode = 2 # FEP_TE_MODE_EV3x3
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 32
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3750
windowSlotIndex = 65535
2024:289:04:20:10.364 3013601 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 43071
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_007ACB is WT007AC024 and is stored.
>>>ERROR: WE ARE DOING A CTI MEASUREMENT BUT WE ARE NOT IN FMT 2!
====> CHANDRA STATUS ARRAY=(HRC-S,HETG-IN,LETG-OUT,43071,OORMPDS,CSELFMT6,ENAB)
2024:289:04:20:11.764 3013606 COMMAND_HW CSELFMT2
2024:289:04:20:14.364 3013616 ACISPKT RS_0000001
2024:289:04:20:18.364 3013632 ACISPKT RH_0000001
2024:289:06:16:57.527 3040946 MP_OBSID 43070
LATEST OCAT INFO FOR OBSID 43070:
No ocat info found for obsid 43070
2024:289:07:02:11.364 3051536 ACISPKT AA00000000
==> ACIS integration time of 8.32 ks.
-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI
-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI
2024:289:07:05:11.364 3052239 ACISPKT AA00000000
2024:289:07:05:11.364 3052239 ORBPOINT EEF1000
==> Entry leg pad time is 10.00 ks.
AE-8 EVENTS TIME CHECK:
from backstop: EE1RADZ0 = 289:07:05:11
from CRM file: EE1RADZ0 = 289:07:05:11
==> CRM Pad Time: 10 ks and Backstop Pad Time: 10.00 ks agree.
2024:289:07:05:20.364 3052274 ACISPKT WSPOW0002A
==> WSPOW COMMAND LOADS: Feps 1 3 5; All vids down
2024:289:07:06:23.364 3052520 ACISPKT RS_0000001
2024:289:08:07:05.747 3066734 MP_OBSID 43069
==> ObsID change occurs 61.9 minutes after stop science.
LATEST OCAT INFO FOR OBSID 43069:
No ocat info found for obsid 43069
2024:289:10:26:12.394 3099306 MP_OBSID 43068
LATEST OCAT INFO FOR OBSID 43068:
No ocat info found for obsid 43068
2024:289:10:35:01.542 REAL-TIME COMM BEGINS 2024:289:06:35:01.542 EDT
2024:289:11:50:00.000 3118926 MP_OBSID 43067
LATEST OCAT INFO FOR OBSID 43067:
No ocat info found for obsid 43067
2024:289:12:02:01.008 3119919 ORBPOINT EPERIGEE
2024:289:12:05:01.542 REAL-TIME COMM ENDS 2024:289:08:05:01.542 EDT
==> COMM DURATION: 90.00 mins.
2024:289:12:36:30.000 3129814 MP_OBSID 43066
LATEST OCAT INFO FOR OBSID 43066:
No ocat info found for obsid 43066
2024:289:13:13:51.979 3138563 MP_OBSID 43065
LATEST OCAT INFO FOR OBSID 43065:
No ocat info found for obsid 43065
2024:289:14:06:34.998 3150907 MP_OBSID 43064
LATEST OCAT INFO FOR OBSID 43064:
No ocat info found for obsid 43064
2024:289:14:13:11.364 3152454 ACISPKT RBTXINGBLL
2024:289:14:23:11.364 3154795 ACISPKT AA00000000
2024:289:14:23:11.364 3154795 ORBPOINT XEF1000
==> The requested SI_MODE for the outbound CTI is TE_007AE
>>>ERROR: Time delta between XE1RADZ0/XEF1000 and EPERIGEE is less than 3.25 hrs.
2024:289:14:23:15.364 3154811 ACISPKT AA00000000
2024:289:14:23:19.364 3154826 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:289:14:23:43.364 3154920 ACISPKT WSPOW3F03F
==> WSPOW COMMAND LOADS: All Feps; std S array
2024:289:14:24:46.364 3155166 ACISPKT WT007AE024
ACIS PBLOCK LOADS:
parameterBlockId = 0x007ae024
fepCcdSelect = 9 7 5 6 4 8
fepMode = 2 # FEP_TE_MODE_EV3x3
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 32
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3750
windowSlotIndex = 65535
2024:289:14:24:50.364 3155181 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 43064
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_007AEB is WT007AE024 and is stored.
====> CHANDRA STATUS ARRAY=(HRC-S,HETG-IN,LETG-OUT,43064,OORMPDS,CSELFMT2,ENAB)
2024:289:14:24:54.364 3155197 ACISPKT RS_0000001
2024:289:14:24:58.364 3155213 ACISPKT RH_0000001
2024:289:15:20:28.061 3168207 MP_OBSID 43063
==> ObsID change occurs 57.2 minutes after stop science.
LATEST OCAT INFO FOR OBSID 43063:
No ocat info found for obsid 43063
2024:289:16:55:52.691 3190547 COMMAND_HW CSELFMT6
>>>ERROR: CHANGE FROM FMT2 OCCURS BEFORE A STOP SCIENCE!
2024:289:16:56:27.030 3190681 COMMAND_SW 4OHETGRE
2024:289:17:00:10.491 3191553 COMMAND_HW CSELFMT2
2024:289:17:06:51.364 3193117 ACISPKT AA00000000
==> ACIS integration time of 0.62 ks.
-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI
-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI
2024:289:17:09:50.364 3193815 COMMAND_SW OORMPEN
==> Exit leg pad time is 10.00 ks.
AE-8 EVENTS TIME CHECK:
from backstop: XE1RADZ0 = 289:14:23:11
from CRM file: XE1RADZ0 = 289:14:23:11
==> CRM Pad Time: 10 ks and Backstop Pad Time: 10.00 ks agree.
2024:289:17:09:51.364 3193819 SIMTRANS 75624 (ACIS-S)
==> THERE IS A Z-SIM OF 0.00 mm FOR THIS OBSERVATION.
2024:289:17:09:51.364 3193819 ACISPKT AA00000000
2024:289:17:09:52.364 3193823 MP_OBSID 28141
==> ObsID change occurs 0.0 minutes after stop science.
>>>ERROR: ObsID change occurs less than 3 minutes after a stop science command.
LATEST OCAT INFO FOR OBSID 28141:
Target Name: MG J2019+1127 SI Mode: TE_00972
Instrument: ACIS-S Grating: NONE Type: GO
Exposure Time: 26 Remaining Exposure time: 26
Offset: Y: 0 Z: 0 Z-sim:
ACIS Exposure Mode: TE Event TM Format: F Frame Time:
Chips Turned On: NNNN NNYYNN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 25 Obj_Flag: NO
2024:289:17:09:55.364 3193835 ACISPKT AA00000000
2024:289:17:09:59.364 3193851 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:289:17:10:23.364 3193944 ACISPKT WSPOW0C006
==> WSPOW COMMAND LOADS: Feps 1 2; S2 S3
2024:289:17:11:26.364 3194190 ACISPKT WT00972024
ACIS PBLOCK LOADS:
parameterBlockId = 0x00972024
fepCcdSelect = 10 7 6 10 10 10
fepMode = 2 # FEP_TE_MODE_EV3x3
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 30
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:289:17:11:30.364 3194206 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 28141
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_00972B is WT00972024 and is stored.
==> FP instrument, Grating and SIM-Z offsets OK.
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-S,HETG-OUT,LETG-OUT,28141,OORMPEN,CSELFMT2,ENAB)
2024:289:17:11:34.364 3194221 ACISPKT RS_0000001
2024:289:17:11:38.364 3194237 ACISPKT RH_0000001
2024:289:18:25:01.285 REAL-TIME COMM BEGINS 2024:289:14:25:01.285 EDT
2024:289:19:55:01.285 REAL-TIME COMM ENDS 2024:289:15:55:01.285 EDT
==> COMM DURATION: 90.00 mins.
2024:290:00:41:02.364 3299462 ACISPKT AA00000000
==> ACIS integration time of 26.00 ks.
This is 100.00% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:290:00:41:02.364 3299462 SIMTRANS 92904 (ACIS-I)
==> THERE IS A Z-SIM OF 0.00 mm FOR THIS OBSERVATION.
2024:290:00:43:01.764 3299928 SIMFOCUS -536
2024:290:00:44:02.364 3300165 MP_OBSID 30577
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 30577:
Target Name: Abell 168 North SI Mode: TE_006E6
Instrument: ACIS-I Grating: NONE Type: GTO
Exposure Time: 16.3 Remaining Exposure time: 16.3
Offset: Y: 0 Z: 0 Z-sim:
ACIS Exposure Mode: TE Event TM Format: VF Frame Time:
Chips Turned On: YYYY NNNNNN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 25 Obj_Flag: NO
2024:290:00:54:56.681 3302718 ACISPKT AA00000000
2024:290:00:55:00.681 3302734 ACISPKT AA00000000
2024:290:00:55:04.681 3302749 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:290:00:55:28.681 3302843 ACISPKT WSPOW00F1E
==> WSPOW COMMAND LOADS: Feps 1 2 3 4; I0 I1 I2 I3
2024:290:00:56:31.681 3303089 ACISPKT WT006E6034
ACIS PBLOCK LOADS:
parameterBlockId = 0x006e6034
fepCcdSelect = 10 3 2 1 0 10
fepMode = 3 # FEP_TE_MODE_EV5x5
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 31
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:290:00:56:35.681 3303105 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 30577
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_006E6B is WT006E6034 and is stored.
==> FP instrument, Grating and SIM-Z offsets OK.
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-I,HETG-OUT,LETG-OUT,30577,OORMPEN,CSELFMT2,ENAB)
2024:290:00:56:39.681 3303120 ACISPKT RS_0000001
2024:290:00:56:43.681 3303136 ACISPKT RH_0000001
2024:290:01:55:01.285 REAL-TIME COMM BEGINS 2024:289:21:55:01.285 EDT
2024:290:03:25:01.285 REAL-TIME COMM ENDS 2024:289:23:25:01.285 EDT
==> COMM DURATION: 90.00 mins.
2024:290:05:27:13.681 3366472 ACISPKT AA00000000
==> ACIS integration time of 15.00 ks.
This is 92.02% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:290:05:27:13.681 3366472 SIMTRANS 75624 (ACIS-S)
==> THERE IS A Z-SIM OF 0.00 mm FOR THIS OBSERVATION.
2024:290:05:29:13.081 3366938 SIMFOCUS -418
2024:290:05:30:13.681 3367175 MP_OBSID 30569
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 30569:
Target Name: MG J2019+1127 SI Mode: TE_00972
Instrument: ACIS-S Grating: NONE Type: GO
Exposure Time: 26 Remaining Exposure time: 26
Offset: Y: 0 Z: 0 Z-sim:
ACIS Exposure Mode: TE Event TM Format: F Frame Time:
Chips Turned On: NNNN NNYYNN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 25 Obj_Flag: NO
2024:290:05:30:32.481 3367248 SIMFOCUS -468
2024:290:05:45:31.833 3370758 ACISPKT AA00000000
2024:290:05:45:35.833 3370773 ACISPKT AA00000000
2024:290:05:45:39.833 3370789 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:290:05:46:03.833 3370883 ACISPKT WSPOW0C006
==> WSPOW COMMAND LOADS: Feps 1 2; S2 S3
2024:290:05:47:06.833 3371129 ACISPKT WT00972024
ACIS PBLOCK LOADS:
parameterBlockId = 0x00972024
fepCcdSelect = 10 7 6 10 10 10
fepMode = 2 # FEP_TE_MODE_EV3x3
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 30
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:290:05:47:10.833 3371144 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 30569
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_00972B is WT00972024 and is stored.
==> FP instrument, Grating and SIM-Z offsets OK.
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-S,HETG-OUT,LETG-OUT,30569,OORMPEN,CSELFMT2,ENAB)
2024:290:05:47:14.833 3371160 ACISPKT RS_0000001
2024:290:05:47:18.833 3371175 ACISPKT RH_0000001
2024:290:11:45:01.285 REAL-TIME COMM BEGINS 2024:290:07:45:01.285 EDT
2024:290:13:15:01.285 REAL-TIME COMM ENDS 2024:290:09:15:01.285 EDT
==> COMM DURATION: 90.00 mins.
2024:290:13:16:42.833 3476401 ACISPKT AA00000000
==> ACIS integration time of 26.00 ks.
This is 100.00% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:290:13:16:42.833 3476401 SIMTRANS 92904 (ACIS-I)
==> THERE IS A Z-SIM OF 0.00 mm FOR THIS OBSERVATION.
2024:290:13:18:42.233 3476867 SIMFOCUS -536
2024:290:13:19:42.833 3477103 MP_OBSID 30578
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 30578:
Target Name: Abell 168 North SI Mode: TE_006E6
Instrument: ACIS-I Grating: NONE Type: GTO
Exposure Time: 10.4 Remaining Exposure time: 10.4
Offset: Y: 0 Z: 0 Z-sim:
ACIS Exposure Mode: TE Event TM Format: VF Frame Time:
Chips Turned On: YYYY NNNNNN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 25 Obj_Flag: NO
2024:290:13:29:58.871 3479507 ACISPKT AA00000000
2024:290:13:30:02.871 3479523 ACISPKT AA00000000
2024:290:13:30:06.871 3479538 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:290:13:30:30.871 3479632 ACISPKT WSPOW00F1E
==> WSPOW COMMAND LOADS: Feps 1 2 3 4; I0 I1 I2 I3
2024:290:13:31:33.871 3479878 ACISPKT WT006E6034
ACIS PBLOCK LOADS:
parameterBlockId = 0x006e6034
fepCcdSelect = 10 3 2 1 0 10
fepMode = 3 # FEP_TE_MODE_EV5x5
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 31
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:290:13:31:37.871 3479894 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 30578
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_006E6B is WT006E6034 and is stored.
==> FP instrument, Grating and SIM-Z offsets OK.
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-I,HETG-OUT,LETG-OUT,30578,OORMPEN,CSELFMT2,ENAB)
2024:290:13:31:41.871 3479909 ACISPKT RS_0000001
2024:290:13:31:45.871 3479925 ACISPKT RH_0000001
2024:290:16:38:55.871 3523749 ACISPKT AA00000000
==> ACIS integration time of 10.00 ks.
This is 96.15% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:290:16:38:55.871 3523749 SIMTRANS -50504 (HRC-I)
2024:290:16:41:55.871 3524452 COMMAND_HW CSELFMT1
2024:290:16:41:55.871 3524452 MP_OBSID 28379
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 28379:
No ACIS info found for obsid 28379.
This is an HRC-I observation.
2024:290:16:43:49.271 3524894 SIMFOCUS -716
2024:290:16:43:57.211 3524925 ACISPKT AA00000000
2024:290:16:44:01.211 3524941 ACISPKT AA00000000
2024:290:16:44:05.211 3524956 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:290:16:44:29.211 3525050 ACISPKT WSPOW08812
==> WSPOW COMMAND LOADS: Feps 1 4; I3 S3
2024:290:16:45:32.211 3525296 ACISPKT RS_0000001
2024:290:16:45:36.211 3525311 ACISPKT RH_0000001
2024:290:16:45:59.211 3525401 ACISPKT WT00DAA014
ACIS PBLOCK LOADS:
parameterBlockId = 0x00daa014
fepCcdSelect = 10 7 10 10 3 10
fepMode = 2 # FEP_TE_MODE_EV3x3
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 0
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 33
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3750
windowSlotIndex = 4
2024:290:16:46:03.211 3525417 ACISPKT W200138014
ACIS 2D WINDOW BLOCK LOADS:
windowSlotIndex = 4
windowBlockId = 0x00138014
ccdId = 0
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 1
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 2
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 3
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 4
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 5
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 6
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 7
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 8
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 9
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
2024:290:16:46:07.211 3525432 ACISPKT XTZ0000005
====> CHANDRA STATUS ARRAY=(HRC-I,HETG-OUT,LETG-OUT,28379,OORMPEN,CSELFMT1,ENAB)
2024:290:17:16:52.211 3532632 AOENDITH AOENDITH
==> DITHER ENABLED
2024:290:17:18:28.211 SCS-134 Activation: HRC Observation Begun
Time between SI Mode load start and SCS-134 activation is good:
Required Delta T: 2071.0 Actual Delta T: 2071.0
2024:290:17:45:01.285 REAL-TIME COMM BEGINS 2024:290:13:45:01.285 EDT
2024:290:17:56:42.211 3541959 SIMTRANS -99616 (HRC-S)
>>>WARNING: There is a SIM translation from HRC-I to HRC-S 70.58 minutes AFTER an ACIS start science
Confirm this is a NIL test
2024:290:17:56:56.211 3542014 MP_OBSID 28380
==> ObsID change occurs 72.9 minutes after stop science.
>>>ERROR: The OBSID change to 28380 occurs more than 5 mins after a start science.
LATEST OCAT INFO FOR OBSID 28380:
No ACIS info found for obsid 28380.
This is an HRC-S observation.
2024:290:17:59:25.611 3542597 SIMFOCUS -1061
2024:290:18:48:02.696 3553981 SIMTRANS 75624 (ACIS-S)
==> THERE IS A Z-SIM OF 0.00 mm FOR THIS OBSERVATION.
>>>ERROR: SIM TRANSLATION OCCURS 121.92 minutes AFTER A START SCIENCE.
2024:290:18:48:15.696 3554031 ACISPKT AA00000000
==> ACIS integration time of 0.01 ks.
This is 100.00% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:290:18:48:15.696 215PCAOF command: HRC Observation Ends
2024:290:18:48:17.696 3554039 COMMAND_HW CSELFMT2
2024:290:18:48:17.696 3554039 MP_OBSID 28202
==> ObsID change occurs 0.0 minutes after stop science.
>>>ERROR: ObsID change occurs less than 3 minutes after a stop science command.
LATEST OCAT INFO FOR OBSID 28202:
Target Name: FRB20210807D SI Mode: TE_0057A
Instrument: ACIS-S Grating: NONE Type: GO
Exposure Time: 30 Remaining Exposure time: 30
Offset: Y: 0 Z: 0 Z-sim:
ACIS Exposure Mode: TE Event TM Format: VF Frame Time:
Chips Turned On: NNNN NNYYNN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 25 Obj_Flag: NO
2024:290:18:53:40.096 3555297 SIMFOCUS -418
2024:290:18:55:09.496 3555646 SIMFOCUS -468
2024:290:18:55:24.629 3555705 ACISPKT AA00000000
2024:290:18:55:28.629 3555721 ACISPKT AA00000000
2024:290:18:55:32.629 3555737 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:290:18:55:56.629 3555830 ACISPKT WSPOW0C006
==> WSPOW COMMAND LOADS: Feps 1 2; S2 S3
2024:290:18:56:59.629 3556076 ACISPKT WT0057A034
ACIS PBLOCK LOADS:
parameterBlockId = 0x0057a034
fepCcdSelect = 10 7 6 10 10 10
fepMode = 3 # FEP_TE_MODE_EV5x5
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 30
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:290:18:57:03.629 3556092 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 28202
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_0057AB is WT0057A034 and is stored.
==> FP instrument, Grating and SIM-Z offsets OK.
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-S,HETG-OUT,LETG-OUT,28202,OORMPEN,CSELFMT2,ENAB)
2024:290:18:57:07.629 3556107 ACISPKT RS_0000001
2024:290:18:57:11.629 3556123 ACISPKT RH_0000001
2024:290:19:06:45.629 3558363 AOENDITH AOENDITH
==> DITHER ENABLED
2024:290:19:15:01.285 REAL-TIME COMM ENDS 2024:290:15:15:01.285 EDT
==> COMM DURATION: 90.00 mins.
2024:290:19:45:49.918 3560595 ORBPOINT EAPOGEE
2024:291:01:50:01.285 REAL-TIME COMM BEGINS 2024:290:21:50:01.285 EDT
2024:291:03:20:01.285 REAL-TIME COMM ENDS 2024:290:23:20:01.285 EDT
==> COMM DURATION: 90.00 mins.
2024:291:03:33:15.629 3676958 ACISPKT AA00000000
==> ACIS integration time of 30.00 ks.
This is 100.00% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:291:03:33:15.629 3676958 SIMTRANS 92904 (ACIS-I)
==> THERE IS A Z-SIM OF 0.00 mm FOR THIS OBSERVATION.
2024:291:03:35:15.029 3677424 SIMFOCUS -536
2024:291:03:36:15.629 3677660 MP_OBSID 30579
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 30579:
Target Name: Abell 168 North SI Mode: TE_006E6
Instrument: ACIS-I Grating: NONE Type: GTO
Exposure Time: 10.3 Remaining Exposure time: 10.3
Offset: Y: 0 Z: 0 Z-sim:
ACIS Exposure Mode: TE Event TM Format: VF Frame Time:
Chips Turned On: YYYY NNNNNN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 25 Obj_Flag: NO
2024:291:03:46:41.728 3680104 ACISPKT AA00000000
2024:291:03:46:45.728 3680119 ACISPKT AA00000000
2024:291:03:46:49.728 3680135 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:291:03:47:13.728 3680229 ACISPKT WSPOW00F1E
==> WSPOW COMMAND LOADS: Feps 1 2 3 4; I0 I1 I2 I3
2024:291:03:48:16.728 3680474 ACISPKT WT006E6034
ACIS PBLOCK LOADS:
parameterBlockId = 0x006e6034
fepCcdSelect = 10 3 2 1 0 10
fepMode = 3 # FEP_TE_MODE_EV5x5
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 31
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:291:03:48:20.728 3680490 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 30579
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_006E6B is WT006E6034 and is stored.
==> FP instrument, Grating and SIM-Z offsets OK.
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-I,HETG-OUT,LETG-OUT,30579,OORMPEN,CSELFMT2,ENAB)
2024:291:03:48:24.728 3680506 ACISPKT RS_0000001
2024:291:03:48:28.728 3680521 ACISPKT RH_0000001
2024:291:06:55:38.728 3724346 ACISPKT AA00000000
==> ACIS integration time of 10.00 ks.
This is 97.09% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:291:06:55:38.728 3724346 SIMTRANS -50504 (HRC-I)
2024:291:06:58:38.728 3725048 COMMAND_HW CSELFMT1
2024:291:06:58:38.728 3725048 MP_OBSID 27996
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 27996:
No ACIS info found for obsid 27996.
This is an HRC-I observation.
2024:291:06:58:38.728 3725048 ACISPKT AA00000000
2024:291:06:58:42.728 3725064 ACISPKT AA00000000
2024:291:06:58:46.728 3725079 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:291:06:59:10.728 3725173 ACISPKT WSPOW08812
==> WSPOW COMMAND LOADS: Feps 1 4; I3 S3
2024:291:07:00:13.728 3725419 ACISPKT RS_0000001
2024:291:07:00:17.728 3725434 ACISPKT RH_0000001
2024:291:07:00:32.128 3725491 SIMFOCUS -716
2024:291:07:00:40.728 3725524 ACISPKT WT00DAA014
ACIS PBLOCK LOADS:
parameterBlockId = 0x00daa014
fepCcdSelect = 10 7 10 10 3 10
fepMode = 2 # FEP_TE_MODE_EV3x3
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 0
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 33
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3750
windowSlotIndex = 4
2024:291:07:00:44.728 3725540 ACISPKT W200138014
ACIS 2D WINDOW BLOCK LOADS:
windowSlotIndex = 4
windowBlockId = 0x00138014
ccdId = 0
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 1
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 2
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 3
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 4
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 5
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 6
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 7
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 8
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
ccdId = 9
ccdRow = 0
ccdColumn = 0
width = 1023
height = 1023
sampleCycle = 0
lowerEventAmplitude = 0
eventAmplitudeRange = 65535
2024:291:07:00:48.728 3725555 ACISPKT XTZ0000005
====> CHANDRA STATUS ARRAY=(HRC-I,HETG-OUT,LETG-OUT,27996,OORMPEN,CSELFMT1,ENAB)
2024:291:07:21:48.120 3730470 AOENDITH AOENDITH
==> DITHER ENABLED
2024:291:07:33:09.728 SCS-134 Activation: HRC Observation Begun
Time between SI Mode load start and SCS-134 activation is good:
Required Delta T: 2071.0 Actual Delta T: 2071.0
2024:291:11:07:59.728 3783432 SIMTRANS 92904 (ACIS-I)
==> THERE IS A Z-SIM OF 0.00 mm FOR THIS OBSERVATION.
>>>ERROR: SIM TRANSLATION OCCURS 247.18 minutes AFTER A START SCIENCE.
2024:291:11:08:11.728 215PCAOF command: HRC Observation Ends
2024:291:11:08:11.728 3783479 ACISPKT AA00000000
==> ACIS integration time of 0.01 ks.
This is 100.00% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:291:11:08:13.728 3783487 COMMAND_HW CSELFMT2
2024:291:11:08:13.728 3783487 MP_OBSID 28334
==> ObsID change occurs 0.0 minutes after stop science.
>>>ERROR: ObsID change occurs less than 3 minutes after a stop science command.
LATEST OCAT INFO FOR OBSID 28334:
Target Name: Abell 3112 N SI Mode: TE_006E6
Instrument: ACIS-I Grating: NONE Type: GO
Exposure Time: 15 Remaining Exposure time: 15
Offset: Y: 0 Z: 0 Z-sim:
ACIS Exposure Mode: TE Event TM Format: VF Frame Time:
Chips Turned On: YYYY NNNNNN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 25 Obj_Flag: NO
2024:291:11:09:51.526 3783869 ACISPKT AA00000000
2024:291:11:09:55.526 3783884 ACISPKT AA00000000
ACISPKT AND/OR POWER COMMAND ERROR:
2024:291:11:09:59.52 ACISPKT Rule #1 - ERROR LESS THAN 3 min delay between first AA00 and WSPOW
2024:291:11:09:59.526 3783900 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:291:11:10:23.526 3783994 ACISPKT WSPOW00F1E
==> WSPOW COMMAND LOADS: Feps 1 2 3 4; I0 I1 I2 I3
2024:291:11:11:26.526 3784239 ACISPKT WT006E6034
ACIS PBLOCK LOADS:
parameterBlockId = 0x006e6034
fepCcdSelect = 10 3 2 1 0 10
fepMode = 3 # FEP_TE_MODE_EV5x5
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 31
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:291:11:11:30.526 3784255 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 28334
---------------------------------------------------------------------------
>>>ERROR: Parameter block stored does not match SI_MODE:TE_006E6 in OCAT.
Stored parameter block is WT006E6034. Requested is WT006E7034
==> FP instrument, Grating and SIM-Z offsets OK.
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-I,HETG-OUT,LETG-OUT,28334,OORMPEN,CSELFMT2,ENAB)
2024:291:11:11:34.526 3784271 ACISPKT RS_0000001
2024:291:11:11:38.526 3784286 ACISPKT RH_0000001
2024:291:11:12:53.128 3784577 SIMFOCUS -486
2024:291:11:14:14.528 3784895 SIMFOCUS -536
2024:291:11:25:01.285 REAL-TIME COMM BEGINS 2024:291:07:25:01.285 EDT
2024:291:11:25:38.526 3787564 AOENDITH AOENDITH
==> DITHER ENABLED
2024:291:12:40:01.285 REAL-TIME COMM ENDS 2024:291:08:40:01.285 EDT
==> COMM DURATION: 75.00 mins.
2024:291:15:42:08.526 3847623 ACISPKT AA00000000
==> ACIS integration time of 15.00 ks.
This is 100.00% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:291:15:42:08.526 3847623 SIMTRANS 75624 (ACIS-S)
==> THERE IS A Z-SIM OF 0.00 mm FOR THIS OBSERVATION.
2024:291:15:44:07.926 3848089 SIMFOCUS -418
2024:291:15:45:08.526 3848325 MP_OBSID 29807
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 29807:
Target Name: eRASSU J052152.0-503812 SI Mode: TE_0065A
Instrument: ACIS-S Grating: NONE Type: GO
Exposure Time: 15 Remaining Exposure time: 15
Offset: Y: 0 Z: 0 Z-sim:
ACIS Exposure Mode: TE Event TM Format: VF Frame Time:
Chips Turned On: NNNY NNYYYN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 26 Obj_Flag: NO
2024:291:15:45:08.526 3848325 ACISPKT AA00000000
2024:291:15:45:12.526 3848341 ACISPKT AA00000000
2024:291:15:45:16.526 3848357 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:291:15:45:27.326 3848399 SIMFOCUS -468
2024:291:15:45:40.526 3848450 ACISPKT WSPOW1C81E
==> WSPOW COMMAND LOADS: Feps 1 2 3 4; I3 S2 S3 S4
2024:291:15:46:43.526 3848696 ACISPKT WT0065A034
ACIS PBLOCK LOADS:
parameterBlockId = 0x0065a034
fepCcdSelect = 10 7 6 3 8 10
fepMode = 3 # FEP_TE_MODE_EV5x5
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 31
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:291:15:46:47.526 3848712 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 29807
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_0065AB is WT0065A034 and is stored.
==> FP instrument, Grating and SIM-Z offsets OK.
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-S,HETG-OUT,LETG-OUT,29807,OORMPEN,CSELFMT2,ENAB)
2024:291:15:46:51.526 3848727 ACISPKT RS_0000001
2024:291:15:46:55.526 3848743 ACISPKT RH_0000001
2024:291:18:45:01.285 REAL-TIME COMM BEGINS 2024:291:14:45:01.285 EDT
2024:291:20:00:01.285 REAL-TIME COMM ENDS 2024:291:16:00:01.285 EDT
==> COMM DURATION: 75.00 mins.
2024:291:20:11:36.826 3910719 ACISPKT AA00000000
==> ACIS integration time of 14.65 ks.
This is 97.68% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:291:20:11:36.826 3910719 SIMTRANS -99616 (HRC-S)
2024:291:20:14:36.826 3911421 COMMAND_HW CSELFMT6
2024:291:20:14:36.826 3911421 MP_OBSID 43062
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 43062:
No ocat info found for obsid 43062
2024:291:20:15:11.165 3911555 COMMAND_SW 4OHETGIN
2024:291:20:17:14.226 3912035 COMMAND_SW OORMPDS
==>The requested SI_MODE for the inbound CTI is TE_00B26
2024:291:20:17:14.226 3912035 ACISPKT AA00000000
2024:291:20:17:18.226 3912051 ACISPKT AA00000000
2024:291:20:17:22.226 3912067 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:291:20:17:46.226 3912160 ACISPKT WSPOW0AF3F
==> WSPOW COMMAND LOADS: All Feps; I0 I1 I2 I3 S1 S3
2024:291:20:18:49.226 3912406 ACISPKT WT00B26014
ACIS PBLOCK LOADS:
parameterBlockId = 0x00b26014
fepCcdSelect = 3 7 0 1 2 5
fepMode = 2 # FEP_TE_MODE_EV3x3
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 32
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3750
windowSlotIndex = 65535
2024:291:20:18:53.226 3912422 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 43062
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_00B26B is WT00B26014 and is stored.
>>>ERROR: WE ARE DOING A CTI MEASUREMENT BUT WE ARE NOT IN FMT 2!
====> CHANDRA STATUS ARRAY=(HRC-S,HETG-IN,LETG-OUT,43062,OORMPDS,CSELFMT6,ENAB)
2024:291:20:18:54.626 3912427 COMMAND_HW CSELFMT2
2024:291:20:18:57.226 3912437 ACISPKT RS_0000001
2024:291:20:19:01.226 3912453 ACISPKT RH_0000001
2024:291:22:06:48.382 3937691 MP_OBSID 43061
LATEST OCAT INFO FOR OBSID 43061:
No ocat info found for obsid 43061
2024:291:23:00:54.226 3950357 ACISPKT AA00000000
==> ACIS integration time of 8.32 ks.
-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI
-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI
2024:291:23:03:54.226 3951060 ACISPKT AA00000000
2024:291:23:03:54.226 3951060 ORBPOINT EEF1000
==> Entry leg pad time is 10.00 ks.
AE-8 EVENTS TIME CHECK:
from backstop: EE1RADZ0 = 291:23:03:54
from CRM file: EE1RADZ0 = 291:23:03:54
==> CRM Pad Time: 10 ks and Backstop Pad Time: 10.00 ks agree.
2024:291:23:04:03.226 3951095 ACISPKT WSPOW0002A
==> WSPOW COMMAND LOADS: Feps 1 3 5; All vids down
2024:291:23:05:06.226 3951341 ACISPKT RS_0000001
2024:292:00:06:15.232 3965659 MP_OBSID 43060
==> ObsID change occurs 62.4 minutes after stop science.
LATEST OCAT INFO FOR OBSID 43060:
No ocat info found for obsid 43060
2024:292:00:45:01.285 REAL-TIME COMM BEGINS 2024:292:20:45:01.285 EDT
2024:292:02:04:16.083 3993291 MP_OBSID 43059
LATEST OCAT INFO FOR OBSID 43059:
No ocat info found for obsid 43059
2024:292:02:15:01.285 REAL-TIME COMM ENDS 2024:291:22:15:01.285 EDT
==> COMM DURATION: 90.00 mins.
2024:292:03:17:00.000 4010321 MP_OBSID 43058
LATEST OCAT INFO FOR OBSID 43058:
No ocat info found for obsid 43058
2024:292:03:28:57.708 4011314 ORBPOINT EPERIGEE
2024:292:04:02:30.000 4020975 MP_OBSID 43057
LATEST OCAT INFO FOR OBSID 43057:
No ocat info found for obsid 43057
2024:292:04:45:30.201 4031044 MP_OBSID 43056
LATEST OCAT INFO FOR OBSID 43056:
No ocat info found for obsid 43056
2024:292:05:55:56.437 4047537 MP_OBSID 43055
LATEST OCAT INFO FOR OBSID 43055:
No ocat info found for obsid 43055
2024:292:06:29:54.226 4055489 ACISPKT RBTXINGBLL
2024:292:06:39:54.226 4057831 ACISPKT AA00000000
2024:292:06:39:54.226 4057831 ORBPOINT XEF1000
==> The requested SI_MODE for the outbound CTI is TE_007AC
>>>ERROR: Time delta between XE1RADZ0/XEF1000 and EPERIGEE is less than 3.25 hrs.
2024:292:06:39:58.226 4057846 ACISPKT AA00000000
2024:292:06:40:02.226 4057862 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:292:06:40:26.226 4057955 ACISPKT WSPOW0CF3F
==> WSPOW COMMAND LOADS: All Feps; std I array
2024:292:06:41:29.226 4058201 ACISPKT WT007AC024
ACIS PBLOCK LOADS:
parameterBlockId = 0x007ac024
fepCcdSelect = 3 7 0 1 2 6
fepMode = 2 # FEP_TE_MODE_EV3x3
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 32
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3750
windowSlotIndex = 65535
2024:292:06:41:33.226 4058217 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 43055
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_007ACB is WT007AC024 and is stored.
====> CHANDRA STATUS ARRAY=(HRC-S,HETG-IN,LETG-OUT,43055,OORMPDS,CSELFMT2,ENAB)
2024:292:06:41:37.226 4058232 ACISPKT RS_0000001
2024:292:06:41:41.226 4058248 ACISPKT RH_0000001
2024:292:07:18:31.003 4066872 MP_OBSID 43054
==> ObsID change occurs 38.5 minutes after stop science.
LATEST OCAT INFO FOR OBSID 43054:
No ocat info found for obsid 43054
2024:292:09:15:49.298 4094338 COMMAND_HW CSELFMT6
>>>ERROR: CHANGE FROM FMT2 OCCURS BEFORE A STOP SCIENCE!
2024:292:09:16:23.637 4094472 COMMAND_SW 4OHETGRE
2024:292:09:20:07.098 4095344 COMMAND_HW CSELFMT2
2024:292:09:23:34.226 4096152 ACISPKT AA00000000
==> ACIS integration time of 0.43 ks.
-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI
-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI
2024:292:09:26:33.226 4096851 COMMAND_SW OORMPEN
==> Exit leg pad time is 10.00 ks.
AE-8 EVENTS TIME CHECK:
from backstop: XE1RADZ0 = 292:06:39:54
from CRM file: XE1RADZ0 = 292:06:39:54
==> CRM Pad Time: 10 ks and Backstop Pad Time: 10.00 ks agree.
2024:292:09:26:34.226 4096855 SIMTRANS 75624 (ACIS-S)
==> THERE IS A Z-SIM OF 0.00 mm FOR THIS OBSERVATION.
2024:292:09:26:34.226 4096855 ACISPKT AA00000000
2024:292:09:26:35.226 4096859 MP_OBSID 29804
==> ObsID change occurs 0.0 minutes after stop science.
>>>ERROR: ObsID change occurs less than 3 minutes after a stop science command.
LATEST OCAT INFO FOR OBSID 29804:
Target Name: eRASSU J062748.5-260240 SI Mode: TE_004A6
Instrument: ACIS-S Grating: NONE Type: GO
Exposure Time: 15 Remaining Exposure time: 15
Offset: Y: 0 Z: 0 Z-sim:
ACIS Exposure Mode: TE Event TM Format: VF Frame Time:
Chips Turned On: NNYY NNYYYN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 26 Obj_Flag: NO
2024:292:09:26:38.226 4096871 ACISPKT AA00000000
2024:292:09:26:42.226 4096886 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:292:09:27:06.226 4096980 ACISPKT WSPOW1CC3E
==> WSPOW COMMAND LOADS: Feps 1 2 3 4 5; I2 I3 S2 S3 S4
2024:292:09:28:09.226 4097226 ACISPKT WT004A6024
ACIS PBLOCK LOADS:
parameterBlockId = 0x004a6024
fepCcdSelect = 10 7 6 3 8 2
fepMode = 3 # FEP_TE_MODE_EV5x5
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 31
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:292:09:28:13.226 4097241 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 29804
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_004A6B is WT004A6024 and is stored.
==> FP instrument, Grating and SIM-Z offsets OK.
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-S,HETG-OUT,LETG-OUT,29804,OORMPEN,CSELFMT2,ENAB)
2024:292:09:28:17.226 4097257 ACISPKT RS_0000001
2024:292:09:28:21.226 4097272 ACISPKT RH_0000001
2024:292:10:20:01.285 REAL-TIME COMM BEGINS 2024:292:06:20:01.285 EDT
2024:292:11:50:01.285 REAL-TIME COMM ENDS 2024:292:07:50:01.285 EDT
==> COMM DURATION: 90.00 mins.
2024:292:14:00:51.226 4161077 ACISPKT AA00000000
==> ACIS integration time of 15.00 ks.
This is 100.00% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:292:14:00:51.226 4161077 SIMTRANS 92904 (ACIS-I)
==> THERE IS A Z-SIM OF 0.00 mm FOR THIS OBSERVATION.
2024:292:14:02:50.626 4161543 SIMFOCUS -536
2024:292:14:03:51.226 4161780 MP_OBSID 30574
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 30574:
Target Name: Abell 370 SI Mode: TE_006E6
Instrument: ACIS-I Grating: NONE Type: GO
Exposure Time: 15 Remaining Exposure time: 15
Offset: Y: 0 Z: 0 Z-sim:
ACIS Exposure Mode: TE Event TM Format: VF Frame Time:
Chips Turned On: YYYY NNNNNN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 25 Obj_Flag: NO
2024:292:14:07:24.504 4162612 ACISPKT AA00000000
2024:292:14:07:28.504 4162628 ACISPKT AA00000000
2024:292:14:07:32.504 4162643 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:292:14:07:56.504 4162737 ACISPKT WSPOW00F1E
==> WSPOW COMMAND LOADS: Feps 1 2 3 4; I0 I1 I2 I3
2024:292:14:08:59.504 4162983 ACISPKT WT006E6034
ACIS PBLOCK LOADS:
parameterBlockId = 0x006e6034
fepCcdSelect = 10 3 2 1 0 10
fepMode = 3 # FEP_TE_MODE_EV5x5
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 31
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:292:14:09:03.504 4162998 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 30574
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_006E6B is WT006E6034 and is stored.
==> FP instrument, Grating and SIM-Z offsets OK.
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-I,HETG-OUT,LETG-OUT,30574,OORMPEN,CSELFMT2,ENAB)
2024:292:14:09:07.504 4163014 ACISPKT RS_0000001
2024:292:14:09:11.504 4163030 ACISPKT RH_0000001
2024:292:17:45:01.285 REAL-TIME COMM BEGINS 2024:292:13:45:01.285 EDT
2024:292:18:39:41.504 4226366 ACISPKT AA00000000
==> ACIS integration time of 15.00 ks.
This is 100.00% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:292:18:39:41.504 4226366 SIMTRANS 92560 (ACIS-I)
==> THERE IS A Z-SIM OF -0.87 mm FOR THIS OBSERVATION.
2024:292:18:42:41.504 4227069 MP_OBSID 30570
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 30570:
Target Name: PSR J1101-6101 SI Mode: TE_006E6
Instrument: ACIS-I Grating: NONE Type: GO
Exposure Time: 12 Remaining Exposure time: 12
Offset: Y: -0.3 Z: 0 Z-sim: -0.8775
ACIS Exposure Mode: TE Event TM Format: VF Frame Time:
Chips Turned On: YYYY NNNNNN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 25 Obj_Flag: NO
2024:292:19:15:01.285 REAL-TIME COMM ENDS 2024:292:15:15:01.285 EDT
==> COMM DURATION: 90.00 mins.
2024:292:19:16:41.358 4235029 ACISPKT WSVIDALLDN
2024:292:19:16:59.358 4235099 ACISPKT WSPOW00F1E
==> WSPOW COMMAND LOADS: Feps 1 2 3 4; I0 I1 I2 I3
2024:292:19:18:02.358 4235345 ACISPKT WT006E7034
ACIS PBLOCK LOADS:
parameterBlockId = 0x006e7034
fepCcdSelect = 10 3 2 1 0 10
fepMode = 3 # FEP_TE_MODE_EV5x5
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 0
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 31
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:292:19:18:06.358 4235361 ACISPKT RS_0000001
2024:292:19:18:10.358 4235376 ACISPKT RH_0000001
2024:292:19:18:33.358 4235466 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 30570
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_006E6 is WT006E7034 and is stored.
==> FP instrument, Grating and SIM-Z offsets OK.
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-I,HETG-OUT,LETG-OUT,30570,OORMPEN,CSELFMT2,ENAB)
2024:292:22:38:40.358 4282323 ACISPKT AA00000000
==> ACIS integration time of 12.01 ks.
This is 100.06% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:292:22:38:40.358 4282323 SIMTRANS 92904 (ACIS-I)
==> THERE IS A Z-SIM OF 0.00 mm FOR THIS OBSERVATION.
2024:292:22:41:40.358 4283025 MP_OBSID 30575
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 30575:
Target Name: Abell 370 SI Mode: TE_006E6
Instrument: ACIS-I Grating: NONE Type: GO
Exposure Time: 10 Remaining Exposure time: 10
Offset: Y: 0 Z: 0 Z-sim:
ACIS Exposure Mode: TE Event TM Format: VF Frame Time:
Chips Turned On: YYYY NNNNNN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 25 Obj_Flag: NO
2024:292:23:15:39.042 4290981 ACISPKT WSVIDALLDN
2024:292:23:15:57.042 4291051 ACISPKT WSPOW00F1E
==> WSPOW COMMAND LOADS: Feps 1 2 3 4; I0 I1 I2 I3
2024:292:23:17:00.042 4291297 ACISPKT WT006E7034
ACIS PBLOCK LOADS:
parameterBlockId = 0x006e7034
fepCcdSelect = 10 3 2 1 0 10
fepMode = 3 # FEP_TE_MODE_EV5x5
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 0
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 31
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:292:23:17:04.042 4291313 ACISPKT RS_0000001
2024:292:23:17:08.042 4291328 ACISPKT RH_0000001
2024:292:23:17:31.042 4291418 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 30575
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_006E6 is WT006E7034 and is stored.
==> FP instrument, Grating and SIM-Z offsets OK.
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-I,HETG-OUT,LETG-OUT,30575,OORMPEN,CSELFMT2,ENAB)
2024:293:00:35:01.285 REAL-TIME COMM BEGINS 2024:293:20:35:01.285 EDT
2024:293:02:04:18.042 4330470 ACISPKT AA00000000
==> ACIS integration time of 10.01 ks.
This is 100.07% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:293:02:04:18.042 4330470 SIMTRANS 92560 (ACIS-I)
==> THERE IS A Z-SIM OF -0.87 mm FOR THIS OBSERVATION.
2024:293:02:05:01.285 REAL-TIME COMM ENDS 2024:292:22:05:01.285 EDT
==> COMM DURATION: 90.00 mins.
2024:293:02:07:18.042 4331172 MP_OBSID 30571
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 30571:
Target Name: PSR J1101-6101 SI Mode: TE_006E6
Instrument: ACIS-I Grating: NONE Type: GO
Exposure Time: 10 Remaining Exposure time: 10
Offset: Y: -0.3 Z: 0 Z-sim: -0.8775
ACIS Exposure Mode: TE Event TM Format: VF Frame Time:
Chips Turned On: YYYY NNNNNN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 25 Obj_Flag: NO
2024:293:02:41:22.725 4339151 ACISPKT WSVIDALLDN
2024:293:02:41:40.725 4339222 ACISPKT WSPOW00F1E
==> WSPOW COMMAND LOADS: Feps 1 2 3 4; I0 I1 I2 I3
2024:293:02:42:43.725 4339468 ACISPKT WT006E7034
ACIS PBLOCK LOADS:
parameterBlockId = 0x006e7034
fepCcdSelect = 10 3 2 1 0 10
fepMode = 3 # FEP_TE_MODE_EV5x5
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 0
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 31
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:293:02:42:47.725 4339483 ACISPKT RS_0000001
2024:293:02:42:51.725 4339499 ACISPKT RH_0000001
2024:293:02:43:14.725 4339589 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 30571
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_006E6 is WT006E7034 and is stored.
==> FP instrument, Grating and SIM-Z offsets OK.
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-I,HETG-OUT,LETG-OUT,30571,OORMPEN,CSELFMT2,ENAB)
2024:293:05:30:01.725 4378640 ACISPKT AA00000000
==> ACIS integration time of 10.01 ks.
This is 100.07% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:293:05:30:01.725 4378640 SIMTRANS 92904 (ACIS-I)
==> THERE IS A Z-SIM OF 0.00 mm FOR THIS OBSERVATION.
2024:293:05:33:01.725 4379343 MP_OBSID 30576
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 30576:
Target Name: Abell 370 SI Mode: TE_006E6
Instrument: ACIS-I Grating: NONE Type: GO
Exposure Time: 10 Remaining Exposure time: 10
Offset: Y: 0 Z: 0 Z-sim:
ACIS Exposure Mode: TE Event TM Format: VF Frame Time:
Chips Turned On: YYYY NNNNNN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 25 Obj_Flag: NO
2024:293:06:07:05.285 4387318 ACISPKT WSVIDALLDN
2024:293:06:07:23.285 4387388 ACISPKT WSPOW00F1E
==> WSPOW COMMAND LOADS: Feps 1 2 3 4; I0 I1 I2 I3
2024:293:06:08:26.285 4387634 ACISPKT WT006E7034
ACIS PBLOCK LOADS:
parameterBlockId = 0x006e7034
fepCcdSelect = 10 3 2 1 0 10
fepMode = 3 # FEP_TE_MODE_EV5x5
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 0
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 31
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:293:06:08:30.285 4387649 ACISPKT RS_0000001
2024:293:06:08:34.285 4387665 ACISPKT RH_0000001
2024:293:06:08:57.285 4387755 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 30576
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_006E6 is WT006E7034 and is stored.
==> FP instrument, Grating and SIM-Z offsets OK.
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-I,HETG-OUT,LETG-OUT,30576,OORMPEN,CSELFMT2,ENAB)
2024:293:08:55:44.285 4426806 ACISPKT AA00000000
==> ACIS integration time of 10.01 ks.
This is 100.07% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:293:08:55:44.285 4426806 SIMTRANS 92560 (ACIS-I)
==> THERE IS A Z-SIM OF -0.87 mm FOR THIS OBSERVATION.
2024:293:08:58:44.285 4427509 MP_OBSID 30572
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 30572:
Target Name: PSR J1101-6101 SI Mode: TE_006E6
Instrument: ACIS-I Grating: NONE Type: GO
Exposure Time: 11 Remaining Exposure time: 11
Offset: Y: -0.3 Z: 0 Z-sim: -0.8775
ACIS Exposure Mode: TE Event TM Format: VF Frame Time:
Chips Turned On: YYYY NNNNNN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 25 Obj_Flag: NO
2024:293:09:32:44.731 4435471 ACISPKT WSVIDALLDN
2024:293:09:33:02.731 4435542 ACISPKT WSPOW00F1E
==> WSPOW COMMAND LOADS: Feps 1 2 3 4; I0 I1 I2 I3
2024:293:09:34:05.731 4435788 ACISPKT WT006E7034
ACIS PBLOCK LOADS:
parameterBlockId = 0x006e7034
fepCcdSelect = 10 3 2 1 0 10
fepMode = 3 # FEP_TE_MODE_EV5x5
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 0
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 31
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:293:09:34:09.731 4435803 ACISPKT RS_0000001
2024:293:09:34:13.731 4435819 ACISPKT RH_0000001
2024:293:09:34:36.731 4435909 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 30572
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_006E6 is WT006E7034 and is stored.
==> FP instrument, Grating and SIM-Z offsets OK.
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-I,HETG-OUT,LETG-OUT,30572,OORMPEN,CSELFMT2,ENAB)
2024:293:10:25:01.285 REAL-TIME COMM BEGINS 2024:293:06:25:01.285 EDT
2024:293:11:13:20.858 4451375 ORBPOINT EAPOGEE
2024:293:12:10:01.285 REAL-TIME COMM ENDS 2024:293:08:10:01.285 EDT
==> COMM DURATION: 105.00 mins.
2024:293:12:38:03.731 4478863 ACISPKT AA00000000
==> ACIS integration time of 11.01 ks.
This is 100.06% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:293:12:38:03.731 4478863 SIMTRANS 92904 (ACIS-I)
==> THERE IS A Z-SIM OF 0.00 mm FOR THIS OBSERVATION.
2024:293:12:41:03.731 4479565 MP_OBSID 28604
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 28604:
Target Name: Abell 370 SI Mode: TE_006E6
Instrument: ACIS-I Grating: NONE Type: GO
Exposure Time: 10 Remaining Exposure time: 10
Offset: Y: 0 Z: 0 Z-sim:
ACIS Exposure Mode: TE Event TM Format: VF Frame Time:
Chips Turned On: YYYY NNNNNN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 25 Obj_Flag: NO
2024:293:13:15:03.171 4487524 ACISPKT WSVIDALLDN
2024:293:13:15:21.171 4487594 ACISPKT WSPOW00F1E
==> WSPOW COMMAND LOADS: Feps 1 2 3 4; I0 I1 I2 I3
2024:293:13:16:24.171 4487840 ACISPKT WT006E7034
ACIS PBLOCK LOADS:
parameterBlockId = 0x006e7034
fepCcdSelect = 10 3 2 1 0 10
fepMode = 3 # FEP_TE_MODE_EV5x5
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 0
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 31
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:293:13:16:28.171 4487856 ACISPKT RS_0000001
2024:293:13:16:32.171 4487871 ACISPKT RH_0000001
2024:293:13:16:55.171 4487961 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 28604
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_006E6 is WT006E7034 and is stored.
==> FP instrument, Grating and SIM-Z offsets OK.
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-I,HETG-OUT,LETG-OUT,28604,OORMPEN,CSELFMT2,ENAB)
2024:293:16:03:42.171 4527013 ACISPKT AA00000000
==> ACIS integration time of 10.01 ks.
This is 100.07% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:293:16:03:42.171 4527013 SIMTRANS 92560 (ACIS-I)
==> THERE IS A Z-SIM OF -0.87 mm FOR THIS OBSERVATION.
2024:293:16:06:42.171 4527715 MP_OBSID 30573
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 30573:
Target Name: PSR J1101-6101 SI Mode: TE_006E6
Instrument: ACIS-I Grating: NONE Type: GO
Exposure Time: 11 Remaining Exposure time: 11
Offset: Y: -0.3 Z: 0 Z-sim: -0.8775
ACIS Exposure Mode: TE Event TM Format: VF Frame Time:
Chips Turned On: YYYY NNNNNN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 25 Obj_Flag: NO
2024:293:16:40:41.618 4535674 ACISPKT WSVIDALLDN
2024:293:16:40:59.618 4535744 ACISPKT WSPOW00F1E
==> WSPOW COMMAND LOADS: Feps 1 2 3 4; I0 I1 I2 I3
2024:293:16:42:02.618 4535990 ACISPKT WT006E7034
ACIS PBLOCK LOADS:
parameterBlockId = 0x006e7034
fepCcdSelect = 10 3 2 1 0 10
fepMode = 3 # FEP_TE_MODE_EV5x5
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 0
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 31
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:293:16:42:06.618 4536006 ACISPKT RS_0000001
2024:293:16:42:10.618 4536021 ACISPKT RH_0000001
2024:293:16:42:33.618 4536111 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 30573
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_006E6 is WT006E7034 and is stored.
==> FP instrument, Grating and SIM-Z offsets OK.
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-I,HETG-OUT,LETG-OUT,30573,OORMPEN,CSELFMT2,ENAB)
2024:293:18:05:01.285 REAL-TIME COMM BEGINS 2024:293:14:05:01.285 EDT
2024:293:19:35:01.285 REAL-TIME COMM ENDS 2024:293:15:35:01.285 EDT
==> COMM DURATION: 90.00 mins.
2024:293:19:46:00.618 4579065 ACISPKT AA00000000
==> ACIS integration time of 11.01 ks.
This is 100.06% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:293:19:46:00.618 4579065 SIMTRANS 75624 (ACIS-S)
==> THERE IS A Z-SIM OF 0.00 mm FOR THIS OBSERVATION.
2024:293:19:48:00.018 4579531 SIMFOCUS -418
2024:293:19:49:00.618 4579768 MP_OBSID 28298
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 28298:
Target Name: SDSS J015530.02-085704.0 SI Mode: TE_006C8
Instrument: ACIS-S Grating: NONE Type: GO
Exposure Time: 22 Remaining Exposure time: 22
Offset: Y: 0 Z: 0 Z-sim:
ACIS Exposure Mode: TE Event TM Format: VF Frame Time:
Chips Turned On: NNNN NYYYYN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 25 Obj_Flag: NO
2024:293:19:49:19.418 4579841 SIMFOCUS -468
2024:293:20:02:08.204 4582841 ACISPKT AA00000000
2024:293:20:02:12.204 4582857 ACISPKT AA00000000
2024:293:20:02:16.204 4582872 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:293:20:02:40.204 4582966 ACISPKT WSPOW1E01E
==> WSPOW COMMAND LOADS: Feps 1 2 3 4; S1 S2 S3 S4
2024:293:20:03:43.204 4583212 ACISPKT WT006C8034
ACIS PBLOCK LOADS:
parameterBlockId = 0x006c8034
fepCcdSelect = 10 7 5 6 8 10
fepMode = 3 # FEP_TE_MODE_EV5x5
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 31
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:293:20:03:47.204 4583227 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 28298
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_006C8B is WT006C8034 and is stored.
==> FP instrument, Grating and SIM-Z offsets OK.
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-S,HETG-OUT,LETG-OUT,28298,OORMPEN,CSELFMT2,ENAB)
2024:293:20:03:51.204 4583243 ACISPKT RS_0000001
2024:293:20:03:55.204 4583259 ACISPKT RH_0000001
2024:294:00:45:01.285 REAL-TIME COMM BEGINS 2024:294:20:45:01.285 EDT
2024:294:02:14:25.204 4670010 ACISPKT AA00000000
==> ACIS integration time of 21.00 ks.
This is 95.45% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:294:02:14:25.204 4670010 SIMTRANS 92904 (ACIS-I)
==> THERE IS A Z-SIM OF 0.00 mm FOR THIS OBSERVATION.
2024:294:02:15:01.285 REAL-TIME COMM ENDS 2024:293:22:15:01.285 EDT
==> COMM DURATION: 90.00 mins.
2024:294:02:16:24.604 4670476 SIMFOCUS -536
2024:294:02:17:25.204 4670712 MP_OBSID 28713
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 28713:
Target Name: 1E 2215.7-0404 / 1E 2216.0-0401 SI Mode: TE_006E6
Instrument: ACIS-I Grating: NONE Type: GO
Exposure Time: 29 Remaining Exposure time: 29
Offset: Y: 0 Z: 0 Z-sim:
ACIS Exposure Mode: TE Event TM Format: VF Frame Time:
Chips Turned On: YYYY NNNNNN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.004444 deg Y Freq: 0.254600 deg/sec Y Phase: 0
Z Amp: 0.004444 deg Z Freq: 0.180000 deg/sec Z Phase: 0
Cycle: 25 Obj_Flag: NO
2024:294:02:27:01.218 4672960 ACISPKT AA00000000
2024:294:02:27:05.218 4672976 ACISPKT AA00000000
2024:294:02:27:09.218 4672991 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:294:02:27:33.218 4673085 ACISPKT WSPOW00F1E
==> WSPOW COMMAND LOADS: Feps 1 2 3 4; I0 I1 I2 I3
2024:294:02:28:36.218 4673331 ACISPKT WT006E6034
ACIS PBLOCK LOADS:
parameterBlockId = 0x006e6034
fepCcdSelect = 10 3 2 1 0 10
fepMode = 3 # FEP_TE_MODE_EV5x5
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 31
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:294:02:28:40.218 4673347 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 28713
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_006E6B is WT006E6034 and is stored.
==> FP instrument, Grating and SIM-Z offsets OK.
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-I,HETG-OUT,LETG-OUT,28713,OORMPEN,CSELFMT2,ENAB)
2024:294:02:28:44.218 4673362 ACISPKT RS_0000001
2024:294:02:28:48.218 4673378 ACISPKT RH_0000001
2024:294:10:15:01.285 REAL-TIME COMM BEGINS 2024:294:06:15:01.285 EDT
2024:294:10:55:31.195 4792024 ACISPKT AA00000000
==> ACIS integration time of 29.17 ks.
This is 100.60% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
2024:294:10:55:31.195 4792024 SIMTRANS -99616 (HRC-S)
2024:294:10:58:31.195 4792726 COMMAND_HW CSELFMT6
2024:294:10:58:31.195 4792726 MP_OBSID 43053
==> ObsID change occurs 3.0 minutes after stop science.
LATEST OCAT INFO FOR OBSID 43053:
No ocat info found for obsid 43053
2024:294:10:59:05.534 4792860 COMMAND_SW 4OHETGIN
2024:294:11:01:31.595 4793430 COMMAND_SW OORMPDS
==>The requested SI_MODE for the inbound CTI is TE_00C60
2024:294:11:01:31.595 4793430 ACISPKT AA00000000
2024:294:11:01:35.595 4793446 ACISPKT AA00000000
2024:294:11:01:39.595 4793461 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:294:11:02:03.595 4793555 ACISPKT WSPOW08F3E
==> WSPOW COMMAND LOADS: Feps 1 2 3 4 5; I0 I1 I2 I3 S3
2024:294:11:02:48.995 4793732 COMMAND_HW CSELFMT2
2024:294:11:03:06.595 4793801 ACISPKT WT00C60014
ACIS PBLOCK LOADS:
parameterBlockId = 0x00c60014
fepCcdSelect = 10 7 3 2 1 0
fepMode = 2 # FEP_TE_MODE_EV3x3
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 32
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3750
windowSlotIndex = 65535
2024:294:11:03:10.595 4793816 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 43053
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_00C60B is WT00C60014 and is stored.
====> CHANDRA STATUS ARRAY=(HRC-S,HETG-IN,LETG-OUT,43053,OORMPDS,CSELFMT2,ENAB)
2024:294:11:03:14.595 4793832 ACISPKT RS_0000001
2024:294:11:03:18.595 4793848 ACISPKT RH_0000001
2024:294:11:45:01.285 REAL-TIME COMM ENDS 2024:294:07:45:01.285 EDT
==> COMM DURATION: 90.00 mins.
2024:294:13:02:38.286 4821788 MP_OBSID 43052
LATEST OCAT INFO FOR OBSID 43052:
No ocat info found for obsid 43052
2024:294:13:45:11.595 4831752 ACISPKT AA00000000
==> ACIS integration time of 8.32 ks.
-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI
-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI
2024:294:13:48:11.595 4832454 ACISPKT AA00000000
2024:294:13:48:11.595 4832454 ORBPOINT EEF1000
==> Entry leg pad time is 10.00 ks.
AE-8 EVENTS TIME CHECK:
from backstop: EE1RADZ0 = 294:13:48:11
from CRM file: EE1RADZ0 = 294:13:48:11
==> CRM Pad Time: 10 ks and Backstop Pad Time: 10.00 ks agree.
2024:294:13:48:20.595 4832489 ACISPKT WSPOW0002A
==> WSPOW COMMAND LOADS: Feps 1 3 5; All vids down
2024:294:13:49:23.595 4832735 ACISPKT RS_0000001
2024:294:15:00:36.634 4849411 MP_OBSID 43051
==> ObsID change occurs 72.4 minutes after stop science.
LATEST OCAT INFO FOR OBSID 43051:
No ocat info found for obsid 43051
2024:294:16:35:01.542 REAL-TIME COMM BEGINS 2024:294:12:35:01.542 EDT
2024:294:17:24:02.405 4882994 MP_OBSID 43050
LATEST OCAT INFO FOR OBSID 43050:
No ocat info found for obsid 43050
2024:294:18:05:01.542 REAL-TIME COMM ENDS 2024:294:14:05:01.542 EDT
==> COMM DURATION: 90.00 mins.
2024:294:18:45:00.000 4901951 MP_OBSID 43049
LATEST OCAT INFO FOR OBSID 43049:
No ocat info found for obsid 43049
2024:294:18:57:20.245 4902943 ORBPOINT EPERIGEE
2024:294:19:31:30.000 4912838 MP_OBSID 43048
LATEST OCAT INFO FOR OBSID 43048:
No ocat info found for obsid 43048
2024:294:20:17:22.381 4923579 MP_OBSID 43047
LATEST OCAT INFO FOR OBSID 43047:
No ocat info found for obsid 43047
>>>WARNING: An ACIS COMMAND is in the vehicle load. Check for SAR.
2024:294:21:10:03.595 4935916 ACISPKT RBTXINGBLL
>>>WARNING: An ACIS COMMAND is in the vehicle load. Check for SAR.
2024:294:21:10:07.595 4935931 ACISPKT WBTXB32020
2024:294:21:10:11.595 4935947 ACISPKT RBTXINGBLL
2024:294:21:16:34.676 4937442 MP_OBSID 43046
LATEST OCAT INFO FOR OBSID 43046:
No ocat info found for obsid 43046
2024:294:21:20:11.595 4938288 ACISPKT AA00000000
2024:294:21:20:11.595 4938288 ORBPOINT XEF1000
==> The requested SI_MODE for the outbound CTI is TE_00B26
>>>ERROR: Time delta between XE1RADZ0/XEF1000 and EPERIGEE is less than 3.25 hrs.
2024:294:21:20:15.595 4938304 ACISPKT AA00000000
2024:294:21:20:19.595 4938320 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:294:21:20:43.595 4938413 ACISPKT WSPOW0AF3F
==> WSPOW COMMAND LOADS: All Feps; I0 I1 I2 I3 S1 S3
2024:294:21:21:46.595 4938659 ACISPKT WT00B26014
ACIS PBLOCK LOADS:
parameterBlockId = 0x00b26014
fepCcdSelect = 3 7 0 1 2 5
fepMode = 2 # FEP_TE_MODE_EV3x3
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 32
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3750
windowSlotIndex = 65535
2024:294:21:21:50.595 4938675 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 43046
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_00B26B is WT00B26014 and is stored.
====> CHANDRA STATUS ARRAY=(HRC-S,HETG-IN,LETG-OUT,43046,OORMPDS,CSELFMT2,ENAB)
2024:294:21:21:54.595 4938690 ACISPKT RS_0000001
2024:294:21:21:58.595 4938706 ACISPKT RH_0000001
2024:294:22:31:34.627 4955003 MP_OBSID 43045
==> ObsID change occurs 71.3 minutes after stop science.
LATEST OCAT INFO FOR OBSID 43045:
No ocat info found for obsid 43045
2024:294:23:47:14.794 4972720 COMMAND_HW CSELFMT6
>>>ERROR: CHANGE FROM FMT2 OCCURS BEFORE A STOP SCIENCE!
2024:294:23:47:49.133 4972854 COMMAND_SW 4OHETGRE
2024:294:23:51:32.594 4973727 COMMAND_HW CSELFMT2
2024:295:00:03:51.595 4976610 ACISPKT AA00000000
==> ACIS integration time of 0.96 ks.
-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI
-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI-CTI
2024:295:00:06:50.595 4977309 COMMAND_SW OORMPEN
==> Exit leg pad time is 10.00 ks.
AE-8 EVENTS TIME CHECK:
from backstop: XE1RADZ0 = 294:21:20:11
from CRM file: XE1RADZ0 = 294:21:20:11
==> CRM Pad Time: 10 ks and Backstop Pad Time: 10.00 ks agree.
2024:295:00:06:51.595 4977313 SIMTRANS 75624 (ACIS-S)
==> THERE IS A Z-SIM OF 0.00 mm FOR THIS OBSERVATION.
2024:295:00:06:51.595 4977313 ACISPKT AA00000000
2024:295:00:06:52.595 4977317 MP_OBSID 25546
==> ObsID change occurs 0.0 minutes after stop science.
>>>ERROR: ObsID change occurs less than 3 minutes after a stop science command.
LATEST OCAT INFO FOR OBSID 25546:
Target Name: SDSS J094533.99+100950.1 SI Mode: TE_005C6
Instrument: ACIS-S Grating: NONE Type: GO
Exposure Time: 3.6 Remaining Exposure time: 3.6
Offset: Y: 0 Z: 0 Z-sim:
ACIS Exposure Mode: TE Event TM Format: VF Frame Time:
Chips Turned On: NNNN NNYYYN
Subarray Type: NONE Start: Rows: Frame Time:
Duty Cycle: N Number: Tprimary: Tsecondary:
Onchip Summing: N Rows: 1 Columns: 1
Event Filter: N Lower: Range:
Window Filter: N Start Row: Start Column:
Height: Width:
Lower Energy: Energy Range: Sample Rate:
Dither: Y
Y Amp: 0.002222 deg Y Freq: 0.360000 deg/sec Y Phase: 0
Z Amp: 0.002222 deg Z Freq: 0.509100 deg/sec Z Phase: 0
Cycle: 25 Obj_Flag: NO
2024:295:00:06:55.595 4977328 ACISPKT AA00000000
2024:295:00:06:59.595 4977344 ACISPKT WSPOW00000
==> WSPOW COMMAND LOADS: All Feps down; All vids down
2024:295:00:07:23.595 4977438 ACISPKT WSPOW1C00E
==> WSPOW COMMAND LOADS: Feps 1 2 3; S2 S3 S4
2024:295:00:08:26.595 4977684 ACISPKT WT005C6024
ACIS PBLOCK LOADS:
parameterBlockId = 0x005c6024
fepCcdSelect = 10 7 6 8 10 10
fepMode = 3 # FEP_TE_MODE_EV5x5
bepPackingMode = 0 # BEP_TE_MODE_FAINT
recomputeBias = 1
trickleBias = 1
subarrayStartRow = 0
subarrayRowCount = 1023
primaryExposure = 31
secondaryExposure = 0
dutyCycle = 0
lowerEventAmplitude = 20
eventAmplitudeRange = 3250
windowSlotIndex = 65535
2024:295:00:08:30.595 4977699 ACISPKT XTZ0000005
---------------------------------------------------------------------------
Parameter block and set up check for 25546
---------------------------------------------------------------------------
==> Parameter Block for SI mode TE_005C6B is WT005C6024 and is stored.
==> FP instrument, Grating and SIM-Z offsets OK.
==> Parameter Block and OCAT are consistent for this observation
====> CHANDRA STATUS ARRAY=(ACIS-S,HETG-OUT,LETG-OUT,25546,OORMPEN,CSELFMT2,ENAB)
2024:295:00:08:34.595 4977715 ACISPKT RS_0000001
2024:295:00:08:38.595 4977730 ACISPKT RH_0000001
2024:295:00:12:28.995 4978630 SIMFOCUS -418
2024:295:00:13:48.395 4978939 SIMFOCUS -468
2024:295:00:21:14.595 4980681 AOENDITH AOENDITH
==> DITHER ENABLED
2024:295:01:27:44.595 4996251 ACISPKT AA00000000
==> ACIS integration time of 3.60 ks.
This is 100.00% of the requested time.
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@-@
-- CHANDRA LOAD END --
************************
ACIS LOAD REVIEW SUMMARY
************************
THERE ARE 23 REAL-TIME COMM PASSAGES IN THIS LOAD.
FREQUENCY OF ACIS COMMAND OCCURRENCES TABLE:
----------------------------------------------------------------------
OBSIDs WSVIDALLDNs RS_0000001 RH_0000001 X[TC]Z0000005 AA00000000
----------------------------------------------------------------------
60 42 42 38 38 100
**NOTE: There are 3 perigee crossings in this load.
FREQUENCY OF OTG INSERTIONS/RETRACTIONS:
--------------------------------------------
LETG_INs LETG_REs HETG_INs HETG_REs
--------------------------------------------
0 0 3 3
--------------------------------------------------------------------------
--------------------------------------------------------------------------
--------------------------------------------------------------------------
AT LEAST ONE INSTANCE OF THE FOLLOWING TYPES OF WARNINGS OR ERRORS WERE ENCOUNTERED:
o. Either Radmon was NOT ENABLED at least 15 ks after an electron 1 exit.
-OR- Radmon was NOT enabled after electron 1 exit.
o. The OBSID change to 30566 that occurs less than 3 mins after a stop science.
o. There is a SIM translation that occurs DURING an ACIS science run.
o. The OBSID change to 30563 that occurs less than 3 mins after a stop science.
o. The OBSID change to 28549 that occurs less than 3 mins after a stop science.
o. RadMon was disabled prior to radbelt transit but we were NOT at HRC-S yet.
o. There is a change from FMT2 before an ACIS stop science.
o. The OBSID change to 28141 that occurs less than 3 mins after a stop science.
o. The OBSID change to 28380 occurs more than 5 mins after a start science.
o. The OBSID change to 28202 that occurs less than 3 mins after a stop science.
o. The OBSID change to 28334 that occurs less than 3 mins after a stop science.
o. The parameter block stored does not match the SI_mode.
o. The OBSID change to 29804 that occurs less than 3 mins after a stop science.
o. An ACIS command is in the vehicle load. Check for SAR.
o. The OBSID change to 25546 that occurs less than 3 mins after a stop science.
o. The Instrument, SIM-Z or Grating was incorrect for obsid(s)
- 30566
- 30563
- 28321
- 28549
- 28600
- 28352
- 28827
- 28553
o. The parameter block was incorrect for obsid(s)
- 28334
--------------------------------------------------------------------------
ACIS LOAD REVIEW FAILED